VialTweeterIntensive Sonication of Small Volumes

Sonication is a very effective method for the mixing, homogenizing, emulsifying, dispersing, disintegration, and degassing of liquids by means of ultrasonic cavitation. The VialTweeter applies this technology to vials, such as autosampler vials, storage vials and reagent vials without the need to open the cap or any water bath.

The production of this model of the VialTweeter has been discontinued and is replaced by the digital model UP200St with VialTweeter. Please visit the page of the UP200St with VialTweeter for the most current information.
Of course, we still supply sonotrodes, accessories and services for both models!

The VialTweeter is an effective alternative to the sonication of vials in ultrasonic cleaning baths or tanks, in which the water surrounding the vials takes most of the energywhile the effective power in a 1.5ml vial is as low as 0.01 watt. For sonication processes, this is no power at all.

The VialTweeter delivers up to 10 watts to each of the six vials in its high intensity part and up to 5 watts to the two vials placed in its low intensity part. These power levels allow for sophisticated sonication processes (see a list at the end of this page) in short time, similar to direct sonication by a homogenizer.

Ultrasonication of vials or beakers at the front end of the VialTweeter.The VialTweeter can sonicate a test tube, bottle or beaker of up to 500ml volume attached to its end, too. The power can be adjusted by means of the amplitude adjustment at the front panel of the generator. Once set, the amplitude will be maintained at the adjusted value and will is distributed evenly across the 6 high intensity vials and the 2 low intensity vials, respectively. This gives you reproducible sonication effects.

The VialTweeter is powered by the ultrasonic processor UIS250v (250 watts, 24kHz). This compact and reliable unit is easy to set-up and operate. As the ultrasonic generator is tuned to the frequency of the sonotrode automatically, there is no manual frequency tuning required. For a good transmission of the ultrasonic vibrations to the individual vials, the vials are pushed gently into the holes of the VialTweeter. Each hole of the VialTweeter is made to hold vials of the most common sizes, brands and designs, such as

  • vials and test tubes of 0.5ml, 1.0ml, 1.5ml or 2.0ml volume, e.g. 12x32mm or 15x45mm
  • vials made by Eppendorf, Greenwood or compatible
  • vials with snap top, crimp top or screw thread finish
  • vials with/without limited volume inserts
  • vials with/without closures
  • conical bottom vials, flat bottom vials, or V-bottom vials
  • microsampling vials, headspace vials, and sample storage vials
  • vials made of polypropylene (PP), polyethylene (PE), polymethylpentene (TPX), polystyrene or PTFE or any other plastic
VialTweeter for simultaneous sonication of various vials.

VialTweeter am UIS250v

Information Request

Note our privacy policy.

The UIS250v can be used with VialTweeter or a sonotrode for direct sonication.

UIS250v with LS24d3

At the end of the VialTweeter, a single vessel can be attached for sonication. You can use vessels, such as

  • bottles, test tubes or beakers
  • vessels of up to 500ml volume
  • vessels of 10mm minimum diameter
  • vessels made of made of glass, polypropylene, polystyrene or any other plastic

The VialTweeter vibrates through the vial/vessel wall. Therefore, the vial can remain closed. Different from the direct sonication by means of an ultrasonic probe/sonotrode (e.g. LS24d5 for UIS250v) that is immersed into the liquid, this eliminates cross contamination of samples. It reduces the time required per vial/vessel. The VialTweeter can be cleaned and disinfected easily.

The VialTweeter is autoclavable while the transducer of the UIS250v is made of stainless steel (IP65, NEMA4). The generator is connected to the transducer by a 4m connection cable.

The UIS250v with VialTweeter can be operated continuously. Pulse cycle operation can be selected at the front panel of the ultrasonic generator. An optionally available PC-interface with software can record the total ultrasonic power and the combined net input power at any Windows®-PC and allows for the remote control of all essential parameters, such as sonication time and amplitude.

Alternatively, the UIS250v can be used for the very intense sonication of one single vial. The sonotrode VT24d10 is designed to deliver up to 15 watts into a single vial. This enables for very sophisticated applications. Sonotrodes for various vial diameters are available.

Stand-mounted Homogenizer UIS250vFor the direct sonication of liquids the UIS250v can be equipped with sonotrodes for immersion into liquids. In that way, the UIS250v can be used as a hand-held or stand-mounted homogenizer.

The exchange between the VialTweeter and the sonotrodes takes approx. 5min.

The VialTweeter as well as the individual sonotrodes can be used in combination with the UIS250v for many applications, such as:

Request a Proposal for this Item!

To receive a proposal, please put your contact details into the form below. A typical device configuration is pre-selected. Feel free to revise the selection before clicking the button to request the proposal.

Please indicate the information, that you wish to receive, below:

  • Ultrasonic Processor UIS250v

  • VialTweeter Sonotrode

    sonotrode for the indirect sonication of up to 8 vials (e.g. Eppendorf), female thread M8x1, with thread bolt M8x1, dimensions (LxWxH) 210x40x50mm preferred vials:

  • Sonotrode LS24d3

    made of titanium, tip diameter 3mm, approx. length 100mm, male thread M8x1, for samples from 5ml up to 100ml

  • Sonotrode LS24d5

    made of titanium, tip diameter 5mm, approx. length 100mm, male thread M8x1, for samples from 10ml up to 200ml

  • Sonotrode LS24d10

    made of titanium, tip diameter 10mm, approx. length 100mm, male thread M8x1, for samples from 20ml up to 400ml

  • Sonotrode VT24d10

    sonotrode for the indirect sonication of 1 vial (e.g. Eppendorf), for vial diameters from 5 to 15mm (please specify below), made of titanium, approx. length 100mm, female thread M8x1, with thread bolt M8x1, requires clamp for stand mounting, e.g. ST1-Clamp diameter (__mm), brand:

  • Stand for lab sample sonication

    diameter 16mm, made of stainless steel, base length 300mm, width 150mm, height 600mm

  • Clamp for lab sample sonication

    clamp for holding diam. 0 to 63mm, made of aluminum, for use with stand stands of up to 16.5mm, e.g. ST1-16

  • LabLift, e.g. for the intense sonication of liquids in glass beakers in the laboratory

    or the easy positioning of samples under the ultrasonic probes to control immersion depth, stainless steel, footprint 100x100mm, adjustable height: 50 to 125mm

  • Timer to predefine sample sonication time

    rom 00:00 to 99:59 (min:sec)

  • Power Meter

    versatile, for display of current power, cumulated energy and cumulated operation time, 115V~1P, 50-60Hz

  • Power Meter

    versatile, for display of current power, cumulated energy and cumulated operation time, 230V~1P, 50-60Hz

Please note our privacy policy.

Larger sample conainers and vials can be clamped to the VialTweeter for indirect sonication.

Sonication with the VialTweeter

Ultrasonic transducer UIS250v with vial holder for the indirect sonication of single test tubes.

UIS250v with VT26d10

We will be glad to discuss your process.

Let's get in contact.